这压环是很实用的道具
可列印查看
这压环是很实用的道具
http://www.my-hiend.com/leoyeh2/2014a/daily001699.jpg
http://www.sibatech.co.jp/abis/tonearm.html
SA-1
* The major key to tonearm quality is the sensitivity and stability in retrieving delicate signals, for which the bearings are the determining factor. The SA-1 employs miniature radial bearings for both horizontal and vertical movement. Very high performance is achieved at a reasonable price.
* The rectangular arm-wand is machined from a solid aluminum block having an advantage in rich and tight bass reproduction, as bass sound is mainly recorded in the horizontal plane of the groove.
* Tonearm wires run through separate aluminum tubes inside the arm so that stereo separation is maximized.
* Reproduced sound is precise and clean, thanks to hand assembly by highly skilled craftsmen.
* Comes with detachable headshell, phono cable (RCA output plug, or optionally as XLR), screws, washers, wrench and marking pin.
Specifications Length: 310mm Spindle center to arm pivot distance: 212mm Stylus to pivot distance: 228mm Overhang: 16mm Cartridge weight: 15-45 grams, including headshell Net weight: 745g (with headshell attached: 762g)
TA-1
* The major key to tonearm quality is the sensitivity and stability in retrieving delicate signals, for which the bearings are the determining factor. The TA-1 employs a miniature radial bearing for horizontal movement and a miniature pivot bearing for vertical movement. Very high performance is achieved at a reasonable price.
* The body is constructed from a machine-tooled solid aluminum block.
* The hand-assembled arm wand satisfies every vital condition necessary for vibration-free and noise-free reproduction.
* Reproduced sound is precise and clean, thanks to hand assembly by highly skilled craftsmen.
* Comes with detachable headshell, phono cable (RCA output plug, or optionally as XLR), screws, washers, wrench and marking pin.
Specifications Length: 305mm Spindle center to arm pivot distance: 216mm Stylus to pivot distance: 232mm Overhang: 16mm Cartridge weight: 15-29 grams, including headshell Net weight: 580g (with headshell attached: 597g)
Ikeda 9TS
與9系列的聲音特色一樣,不過0.35mVrms的輸出比9TT高出一倍,比較容易搭配,價格也稍低(USD 2,800)
http://www.my-hiend.com/leoyeh2/2014a/daily001702.jpg
Tonally it has the same musicality as the other MC cartridges in the "9"-family. No compromises are made also during processing. The 9TS 0, 35mV is about twice as high output voltage compared to the 9TT so that it can be operated without any problems on cheaper phono preamps.
Output Voltage: 0.35mVrms (1kHz 35.4mm/sec., at 45°peak)
Coil Impedance: 6.0 ohms (1kHz)
Appropriate Stylus Force: 2.0grams ±0.2 grams
Frequency Response: 10Hz ~ 45kHz
Channel Separation: over 27dB (1kHz)
Channel Balance: within 1.0dB (1kHz)
Stylus Chip: Oval-shaped solid Diamond
Cantilever: Double layered duralumin pipe.
Weight: 10 grams
Compliance: 7 x 10-6cm/dyne
Ikeda SAI
來自傳奇的9MUSAM,全新毫不妥協的設計,輸出較原來增加,為0.3 mVrms
http://www.my-hiend.com/leoyeh2/2014a/daily001703.jpg
The "SAI", is the uncompromising advancement of the legendary "9MUSAM" with completely brand new pickup system. Engineers from IKEDA succeeded to transfer the tonal qualities of the 9MUSAM without compromising. The output voltage could be increased through further development in the area of the coil drive to 0, a channel equal 0, 5dB 30mV! The cantilever consists of "Boron" and the diamond is "Micro-Ridge."
MC cartridge: Universal type dedicated to tonearm.
Output Voltage: 0.3 mVrms (1kHz 35.4mm/sec., at 45°peak)
Coil Impedance: 2.5 ohms (1kHz)
Appropriate Stylus Force: 2.0grams ±0.2 grams
Frequency Response: 10Hz ~ 45kHz
Channel Separation: over 30dB (1kHz)
Channel Balance: within 0.5dB (1kHz)
Stylus Chip: Micro-ridge solid Diamond
Cantilever: made of Boron.
Weight: 30 grams
Compliance: 7 x 10-6cm/dyne
來一顆High End的SAI吧~~~~~~~~~~~~
請問站長及先進,
FR唱臂你會推薦什麼品牌唱頭?
池田是否比光悅較好搭配?敬請指教。
感謝。