初步挺起來很不錯,但disable 各種led似乎不work,感謝sam兄無私辛苦奉獻
我從使用 Tapatalk 的 SM-G9860 發送
初步挺起來很不錯,但disable 各種led似乎不work,感謝sam兄無私辛苦奉獻
我從使用 Tapatalk 的 SM-G9860 發送
轉Po連結:
有國外樂友在小弟的github上分享在Noël上加工支援一些我看不懂的功能。
---
Hi Sam,
By the way, I have finished adding TC, Aplayer, AP to your piCorePlayer6.1.0-Noel. You can try it here.. (sorry, I set it to overclock: none, because my Pi 4 v1.1 above 65°C).
Members of @ My-hiend, stsd99 can try it.
---
有興趣的樂友可以試試看。
https://drive.google.com/drive/folde...2TbPTIwLV-TQ6G
小弟研究了一下,
AP應該是Album Player,讓piCorePlayer可以單機直接播放音樂,無需Music Server。
TC是Tidal Connect,讓piCorePlayer直接支援Tidal串流。
Ericcatz兄您好
http://albumplayer.ru/linux/english.html
上面是Album Player的官網,裡面有提供操作手冊但是是俄文的。
https://www.dastereo.ru/t/picoreap-d...m-player/37024
另外上面這個俄文的討論串似乎是作者所發起的,有興趣的話也可以參考一下。
使用上面sam兄所公佈由github網兄所提供的img安裝啟動後,樹莓派ip後加上port 7778後就可進入aplayer的介面。
類似這個樣子 http://192.168.3.2:7778
這是小弟臨時加入Album Player的版本,僅僅測試功能用,不是小弟期待的版本。
如果在squeezelite先調好音效卡的設定,看看非USB是否能用。
記得先要把squeezelite STOP,免得互搶。
https://www.dropbox.com/s/30zdfhk8no...er.img.7z?dl=0
這個連結可能只會放個幾天就失效了。
AP 還有 Console 的版本,畢竟 Console 的好處就是省去網路的干擾,或許那個就是聲音方面最好的選擇?
把 ap.sh 那個檔案的最後一行 sudo ./ap "$1" 修改一下就可以把 network 暫時關上/重開:代碼:sudo ifconfig eth0 down
sudo ./ap "$1"
sudo ifconfig eth0 up
另外 Apple M1 的 RAM disk 該是與眾不同:
https://www.macworld.com/article/347...e-release.htmlhttps://www.macworld.com/article/234...sed-to-be.html引用:
The RAM isn’t just soldered onto the motherboard on the M1 MacBook and iMac—it’s built directly into the chip, making it faster and more efficient.
而且 Thunderbolt 方面也是有點相似:引用:
The biggest difference is that in the M1, the memory is a part of the M1 architecture itself. There’s no memory slot or slots on the motherboard of an M1 Mac, nor is there an area where a memory chip has been permanently soldered on. Instead, the memory is integrated into the same package that contains the M1 itself.
https://www.reddit.com/r/mac/comment...erbolt_4_with/把兩台 Apple M1 連接起來的話就變得相當有趣:引用:
Yes, I know because M1 itself has a controller. That's why it does not need a TB controller.
Thunderbolt Networking on Linux
https://christian.kellner.me/2018/05...king-on-linux/
https://github.com/NetworkManager/NetworkManager
https://gitlab.freedesktop.org/Netwo...NetworkManager
Thunderbolt 3 device manager
https://gitlab.freedesktop.org/bolt/bolt
Networking over Thunderbolt cable
https://www.kernel.org/doc/html/v5.1...underbolt.html
還有特別的線材,完全沒有銅線,只有光纖的說:引用:
This triggers module load on the other host automatically. If the driver is built-in to the kernel image, there is no need to do anything.
The driver will create one virtual ethernet interface per Thunderbolt port which are named like thunderbolt0 and so on. From this point you can either use standard userspace tools like ifconfig to configure the interface or let your GUI handle it automatically.
https://www.corning.com/optical-cabl...al-cables.html
https://www.youtube.com/watch?v=Dy312cUHumk